diff options
Diffstat (limited to 'firmware/inc')
| -rw-r--r-- | firmware/inc/bsp.h | 18 | ||||
| -rw-r--r-- | firmware/inc/cmd.h | 74 | ||||
| -rw-r--r-- | firmware/inc/driver/device.h | 25 | ||||
| -rw-r--r-- | firmware/inc/driver/f1956.h | 41 | ||||
| -rw-r--r-- | firmware/inc/driver/mcp3202.h | 82 | ||||
| -rw-r--r-- | firmware/inc/driver/mcp4725.h | 48 | ||||
| -rw-r--r-- | firmware/inc/driver/radio_config.h | 680 | ||||
| -rw-r--r-- | firmware/inc/driver/si4468.h | 54 | ||||
| -rw-r--r-- | firmware/inc/module/drain.h | 37 | ||||
| -rw-r--r-- | firmware/inc/module/gate.h | 32 | ||||
| -rw-r--r-- | firmware/inc/peripheral/ring.h | 77 | ||||
| -rw-r--r-- | firmware/inc/peripheral/spi.h | 34 | ||||
| -rw-r--r-- | firmware/inc/peripheral/timer.h | 22 | ||||
| -rw-r--r-- | firmware/inc/peripheral/twi.h | 35 | ||||
| -rw-r--r-- | firmware/inc/peripheral/uart.h | 56 | ||||
| -rw-r--r-- | firmware/inc/setup.h | 39 | ||||
| -rw-r--r-- | firmware/inc/status.h | 83 | ||||
| -rw-r--r-- | firmware/inc/util.h | 46 |
18 files changed, 1483 insertions, 0 deletions
diff --git a/firmware/inc/bsp.h b/firmware/inc/bsp.h new file mode 100644 index 0000000..2f38cfb --- /dev/null +++ b/firmware/inc/bsp.h @@ -0,0 +1,18 @@ +/** + * + * Author: Dylan Muller + * Copyright (c) 2025 + * All rights reserved. + * + * - Commercial/IP use prohibited. + * - Attribution required. + * See License.txt + * + */ + +#ifndef BSP_H_ +#define BSP_H + +void bsp_soft_reset(void); + +#endif diff --git a/firmware/inc/cmd.h b/firmware/inc/cmd.h new file mode 100644 index 0000000..11d25e0 --- /dev/null +++ b/firmware/inc/cmd.h @@ -0,0 +1,74 @@ +/** + * + * Author: Dylan Muller + * Copyright (c) 2025 + * All rights reserved. + * + * - Commercial/IP use prohibited. + * - Attribution required. + * See License.txt + * + */ + +#ifndef CMD_H_ +#define CMD_H_ + +#include <avr/pgmspace.h> + +#define CMD_MAX_ARGS 5 +#define CMD_NEWLINE "\n" + +#define CMD_DEF_ARG(x) x +#define CMD_DEF_SINGLE(x) x CMD_NEWLINE + +#define CMD_ERROR(x) printf("ERROR %s\n", x) +#define CMD_PRINT(x) printf("INFO %s\n", x) +#define CMD_PRINT_FMT(x, y) printf("INFO " x CMD_NEWLINE, y) +#define CMD_SWITCH(x, y) !strcmp(x, y) + +#define CMD_POWER_GET_STR "POWER?" +#define CMD_POWER_GET_DESC "QUERY RF POWER" + +#define CMD_POWER_SET_STR "POWER" +#define CMD_POWER_SET_DESC "SET RF POWER" + +#define CMD_TX_STR "TX" +#define CMD_TX_DESC "SWITCH TO TX MODE" + +#define CMD_RX_STR "RX" +#define CMD_RX_DESC "SWITCH TO RX MODE" + +#define CMD_DRAIN_SET_STR "DRAIN" +#define CMD_DRAIN_SET_DESC "SET DRAIN COUNTER" + +#define CMD_PROBE_STR "PROBE" +#define CMD_PROBE_DESC "START GATE PROBE" + +#define CMD_RESET_STR "RESET" +#define CMD_RESET_DESC "EXECUTE SOFT RESET" + +#define CMD_REPORT_STR "REPORT" +#define CMD_REPORT_DESC "DUMP SYSTEM REPORT" + +#define CMD_HELP_STR "HELP" +#define CMD_HELP_DESC "DUMP COMMAND LIST" + +#define CMD_LINK_REPLY_STR "REPLY" + +#define CMD_SIZE 9 +#define CMD_ENTRY_SIZE 2 + +#define CMD_POWER_GET CMD_DEF_SINGLE(CMD_POWER_GET_STR) +#define CMD_POWER_SET CMD_DEF_ARG(CMD_POWER_SET_STR) +#define CMD_TX CMD_DEF_SINGLE(CMD_TX_STR) +#define CMD_RX CMD_DEF_SINGLE(CMD_RX_STR) +#define CMD_DRAIN_SET CMD_DEF_ARG(CMD_DRAIN_SET_STR) +#define CMD_PROBE CMD_DEF_SINGLE(CMD_PROBE_STR) +#define CMD_RESET CMD_DEF_SINGLE(CMD_RESET_STR) +#define CMD_REPORT CMD_DEF_SINGLE(CMD_REPORT_STR) +#define CMD_HELP CMD_DEF_SINGLE(CMD_HELP_STR) +#define CMD_LINK_REPLY CMD_DEF_SINGLE(CMD_LINK_REPLY_STR) + +extern const char* const cmd_lut[][2]; + +#endif diff --git a/firmware/inc/driver/device.h b/firmware/inc/driver/device.h new file mode 100644 index 0000000..b8528c2 --- /dev/null +++ b/firmware/inc/driver/device.h @@ -0,0 +1,25 @@ +/** + * + * Author: Dylan Muller + * Copyright (c) 2025 + * All rights reserved. + * + * - Commercial/IP use prohibited. + * - Attribution required. + * See License.txt + * + */ + +#ifndef DEVICE_H_ +#define DEVICE_H_ + +#include <stdint.h> + +typedef struct +{ + uint8_t dev_id; + uint8_t dev_ss; + uint8_t* dev_port; +} t_dev; + +#endif diff --git a/firmware/inc/driver/f1956.h b/firmware/inc/driver/f1956.h new file mode 100644 index 0000000..79c5f0b --- /dev/null +++ b/firmware/inc/driver/f1956.h @@ -0,0 +1,41 @@ +/** + * + * Author: Dylan Muller + * Copyright (c) 2025 + * All rights reserved. + * + * - Commercial/IP use prohibited. + * - Attribution required. + * See License.txt + * + */ + +#ifndef F1956_H_ +#define F1956_H_ + +#include "setup.h" + +#include <stdint.h> +#include <avr/io.h> + +#define F1956_ID_INPUT_ATT 0xC1 + +#define F1956_DEV_0 0 +#define F1956_DEV_INPUT_ATT F1956_DEV_0 + +#define F1956_DEV_INPUT_ATT_ADDR 0x0 + +#define F1956_DEV_0_PORT PORTC +#define F1956_DEV_0_DDR DDRC +#define F1956_DEV_0_SS PORTC2 + +void att_init( + uint8_t init_value +); + +void att_set( + uint8_t id, + uint8_t value +); + +#endif diff --git a/firmware/inc/driver/mcp3202.h b/firmware/inc/driver/mcp3202.h new file mode 100644 index 0000000..b995834 --- /dev/null +++ b/firmware/inc/driver/mcp3202.h @@ -0,0 +1,82 @@ +/** + * + * Author: Dylan Muller + * Copyright (c) 2025 + * All rights reserved. + * + * - Commercial/IP use prohibited. + * - Attribution required. + * See License.txt + * + */ + +#ifndef MCP3202_H_ +#define MCP3202_H_ + +#include <stdint.h> +#include <avr/io.h> + +#define MCP3202_BIT_MSBBF(x) (x << 5) +#define MCP3202_BIT_ODD(x) (x << 6) +#define MCP3202_BIT_SGL(x) (x << 7) +#define MCP3202_BIT_START (1 << 0) + +#define MCP3202_DAQ_MSB 0x2 +#define MCP3202_DAQ_LSB 0x1 + +#define MCP3202_BUILD_REQ(MSBF, ODD, SGL) \ + (uint8_t)(MCP3202_BIT_MSBBF(MSBF) | \ + MCP3202_BIT_ODD(ODD) | \ + MCP3202_BIT_SGL(SGL)) + +#define MCP3202_REQ_START (uint8_t)(MCP3202_BIT_START) +#define MCP3202_REQ_CH0 MCP3202_BUILD_REQ(1, 0, 1) +#define MCP3202_REQ_CH1 MCP3202_BUILD_REQ(1, 1, 1) +#define MCP3202_REQ_PAD (uint8_t)(0x0) + +#define MCP3202_ID_FW_POWER 0xA1 +#define MCP3202_ID_REV_POWER 0xA2 +#define MCP3202_ID_DRAIN_VOLT 0xA3 +#define MCP3202_ID_DRAIN_AMP 0xA4 + +#define MCP3202_CHN_0 0 +#define MCP3202_CHN_1 1 + +#define MCP3202_CHN_DRAIN_VOLT MCP3202_CHN_0 +#define MCP3202_CHN_DRAIN_AMP MCP3202_CHN_1 +#define MCP3202_CHN_FW_POWER MCP3202_CHN_1 +#define MCP3202_CHN_REV_POWER MCP3202_CHN_0 + +#define MCP3202_DEV_0 0 +#define MCP3202_DEV_1 1 + +#define MCP3202_DEV_DRAIN_VOLT MCP3202_DEV_0 +#define MCP3202_DEV_DRAIN_AMP MCP3202_DEV_0 +#define MCP3202_DEV_FW_POWER MCP3202_DEV_1 +#define MCP3202_DEV_REV_POWER MCP3202_DEV_1 + +#define MCP3202_DEV_0_PORT PORTC +#define MCP3202_DEV_0_DDR DDRC +#define MCP3202_DEV_0_SS PORTC0 +#define MCP3202_DEV_1_PORT PORTC +#define MCP3202_DEV_1_DDR DDRC +#define MCP3202_DEV_1_SS PORTC1 + +#define MCP3202_DRAIN_VOLT_GAIN 26 +#define MCP3202_DRAIN_AMP_GAIN 25 + + +void adc_init(void); + +uint16_t adc_read( + uint8_t id, + uint8_t conv_bypass +); + +uint16_t adc_read_n( + uint8_t id, + uint8_t n +); + + +#endif diff --git a/firmware/inc/driver/mcp4725.h b/firmware/inc/driver/mcp4725.h new file mode 100644 index 0000000..06f6281 --- /dev/null +++ b/firmware/inc/driver/mcp4725.h @@ -0,0 +1,48 @@ +/** + * + * Author: Dylan Muller + * Copyright (c) 2025 + * All rights reserved. + * + * - Commercial/IP use prohibited. + * - Attribution required. + * See License.txt + * + */ + +#ifndef MCP4725_H_ +#define MCP4725_H_ + +#define MCP4725_BIT_PD0(x) (x << 4) +#define MCP4725_BIT_PD1(x) (x << 5) + +#define MCP4725_ID_GATE_VOLT 0xB1 +#define MCP4725_ID_DRAIN_VOLT 0xB2 + +#define MCP4725_DEV_0 0 +#define MCP4725_DEV_1 1 + +#define MCP4725_DEV_GATE_VOLT MCP4725_DEV_0 +#define MCP4725_DEV_DRAIN_VOLT MCP4725_DEV_1 + +#define MCP4725_DEV_GATE_VOLT_ADDR 0x60 +#define MCP4725_DEV_DRAIN_VOLT_ADDR 0x61 + +#define MCP4725_DRAIN_GAIN 23 + +void dac_init( + uint16_t init_value +); + +void dac_write( + uint8_t id, + uint16_t value, + uint8_t conv_bypass +); + +uint16_t dac_read( + uint8_t id, + uint8_t conv_bypass +); + +#endif diff --git a/firmware/inc/driver/radio_config.h b/firmware/inc/driver/radio_config.h new file mode 100644 index 0000000..ff079a7 --- /dev/null +++ b/firmware/inc/driver/radio_config.h @@ -0,0 +1,680 @@ +/*! @file radio_config.h + * @brief This file contains the automatically generated + * configurations. + * + * @n WDS GUI Version: 3.2.11.0 + * @n Device: Si4468 Rev.: A2 + * + * @b COPYRIGHT + * @n Silicon Laboratories Confidential + * @n Copyright 2017 Silicon Laboratories, Inc. + * @n http://www.silabs.com + */ + +#ifndef RADIO_CONFIG_H_ +#define RADIO_CONFIG_H_ + +// USER DEFINED PARAMETERS +// Define your own parameters here + +// INPUT DATA +/* +// Crys_freq(Hz): 30000000 Crys_tol(ppm): 20 IF_mode: 2 High_perf_Ch_Fil: 1 OSRtune: 0 Ch_Fil_Bw_AFC: 0 ANT_DIV: 0 PM_pattern: 0 +// MOD_type: 2 Rsymb(sps): 1000 Fdev(Hz): 2000 RXBW(Hz): 150000 Manchester: 0 AFC_en: 0 Rsymb_error: 0.0 Chip-Version: 2 +// RF Freq.(MHz): 169.4 API_TC: 29 fhst: 250000 inputBW: 0 BERT: 0 RAW_dout: 0 D_source: 0 Hi_pfm_div: 1 +// API_ARR_Det_en: 0 Fdev_error: 0 API_ETSI: 0 +// +// # RX IF frequency is -468750 Hz +// # WB filter 1 (BW = 19.08 kHz); NB-filter 1 (BW = 19.08 kHz) +// +// Modulation index: 4 +*/ + + +// CONFIGURATION PARAMETERS +#define RADIO_CONFIGURATION_DATA_RADIO_XO_FREQ 30000000L +#define RADIO_CONFIGURATION_DATA_CHANNEL_NUMBER 0x00 +#define RADIO_CONFIGURATION_DATA_RADIO_PACKET_LENGTH 0x07 +#define RADIO_CONFIGURATION_DATA_RADIO_STATE_AFTER_POWER_UP 0x03 +#define RADIO_CONFIGURATION_DATA_RADIO_DELAY_CNT_AFTER_RESET 0xF000 + + +// CONFIGURATION COMMANDS + +/* +// Command: RF_POWER_UP +// Description: Command to power-up the device and select the operational mode and functionality. +*/ +#define RF_POWER_UP 0x02, 0x01, 0x00, 0x01, 0xC9, 0xC3, 0x80 + +/* +// Command: RF_GPIO_PIN_CFG +// Description: Configures the GPIO pins. +*/ +#define RF_GPIO_PIN_CFG 0x13, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00 + +/* +// Set properties: RF_GLOBAL_XO_TUNE_2 +// Number of properties: 2 +// Group ID: 0x00 +// Start ID: 0x00 +// Default values: 0x40, 0x00, +// Descriptions: +// GLOBAL_XO_TUNE - Configure the internal capacitor frequency tuning bank for the crystal oscillator. +// GLOBAL_CLK_CFG - Clock configuration options. +*/ +#define RF_GLOBAL_XO_TUNE_2 0x11, 0x00, 0x02, 0x00, 0x52, 0x00 + +/* +// Set properties: RF_GLOBAL_CONFIG_1 +// Number of properties: 1 +// Group ID: 0x00 +// Start ID: 0x03 +// Default values: 0x20, +// Descriptions: +// GLOBAL_CONFIG - Global configuration settings. +*/ +#define RF_GLOBAL_CONFIG_1 0x11, 0x00, 0x01, 0x03, 0x20 + +/* +// Set properties: RF_INT_CTL_ENABLE_2 +// Number of properties: 2 +// Group ID: 0x01 +// Start ID: 0x00 +// Default values: 0x04, 0x00, +// Descriptions: +// INT_CTL_ENABLE - This property provides for global enabling of the three interrupt groups (Chip, Modem and Packet Handler) in order to generate HW interrupts at the NIRQ pin. +// INT_CTL_PH_ENABLE - Enable individual interrupt sources within the Packet Handler Interrupt Group to generate a HW interrupt on the NIRQ output pin. +*/ +#define RF_INT_CTL_ENABLE_2 0x11, 0x01, 0x02, 0x00, 0x01, 0xFF + +/* +// Set properties: RF_FRR_CTL_A_MODE_4 +// Number of properties: 4 +// Group ID: 0x02 +// Start ID: 0x00 +// Default values: 0x01, 0x02, 0x09, 0x00, +// Descriptions: +// FRR_CTL_A_MODE - Fast Response Register A Configuration. +// FRR_CTL_B_MODE - Fast Response Register B Configuration. +// FRR_CTL_C_MODE - Fast Response Register C Configuration. +// FRR_CTL_D_MODE - Fast Response Register D Configuration. +*/ +#define RF_FRR_CTL_A_MODE_4 0x11, 0x02, 0x04, 0x00, 0x0A, 0x09, 0x00, 0x00 + +/* +// Set properties: RF_PREAMBLE_TX_LENGTH_9 +// Number of properties: 9 +// Group ID: 0x10 +// Start ID: 0x00 +// Default values: 0x08, 0x14, 0x00, 0x0F, 0x21, 0x00, 0x00, 0x00, 0x00, +// Descriptions: +// PREAMBLE_TX_LENGTH - Configure length of TX Preamble. +// PREAMBLE_CONFIG_STD_1 - Configuration of reception of a packet with a Standard Preamble pattern. +// PREAMBLE_CONFIG_NSTD - Configuration of transmission/reception of a packet with a Non-Standard Preamble pattern. +// PREAMBLE_CONFIG_STD_2 - Configuration of timeout periods during reception of a packet with Standard Preamble pattern. +// PREAMBLE_CONFIG - General configuration bits for the Preamble field. +// PREAMBLE_PATTERN_31_24 - Configuration of the bit values describing a Non-Standard Preamble pattern. +// PREAMBLE_PATTERN_23_16 - Configuration of the bit values describing a Non-Standard Preamble pattern. +// PREAMBLE_PATTERN_15_8 - Configuration of the bit values describing a Non-Standard Preamble pattern. +// PREAMBLE_PATTERN_7_0 - Configuration of the bit values describing a Non-Standard Preamble pattern. +*/ +#define RF_PREAMBLE_TX_LENGTH_9 0x11, 0x10, 0x09, 0x00, 0x08, 0x14, 0x00, 0x0F, 0x31, 0x00, 0x00, 0x00, 0x00 + +/* +// Set properties: RF_SYNC_CONFIG_10 +// Number of properties: 10 +// Group ID: 0x11 +// Start ID: 0x00 +// Default values: 0x01, 0x2D, 0xD4, 0x2D, 0xD4, 0x00, 0x2D, 0xD4, 0x2D, 0xD4, +// Descriptions: +// SYNC_CONFIG - Sync Word configuration bits. +// SYNC_BITS_31_24 - Sync word. +// SYNC_BITS_23_16 - Sync word. +// SYNC_BITS_15_8 - Sync word. +// SYNC_BITS_7_0 - Sync word. +// SYNC_CONFIG2 - Sync Word configuration bits. +// SYNC_BITS2_31_24 - Sync word 2. +// SYNC_BITS2_23_16 - Sync word 2. +// SYNC_BITS2_15_8 - Sync word 2. +// SYNC_BITS2_7_0 - Sync word 2. +*/ +#define RF_SYNC_CONFIG_10 0x11, 0x11, 0x0A, 0x00, 0x01, 0xB4, 0x2B, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00 + +/* +// Set properties: RF_PKT_CRC_CONFIG_12 +// Number of properties: 12 +// Group ID: 0x12 +// Start ID: 0x00 +// Default values: 0x00, 0x01, 0x08, 0xFF, 0xFF, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x30, +// Descriptions: +// PKT_CRC_CONFIG - Select a CRC polynomial and seed. +// PKT_WHT_POLY_15_8 - 16-bit polynomial value for the PN Generator (e.g., for Data Whitening) +// PKT_WHT_POLY_7_0 - 16-bit polynomial value for the PN Generator (e.g., for Data Whitening) +// PKT_WHT_SEED_15_8 - 16-bit seed value for the PN Generator (e.g., for Data Whitening) +// PKT_WHT_SEED_7_0 - 16-bit seed value for the PN Generator (e.g., for Data Whitening) +// PKT_WHT_BIT_NUM - Selects which bit of the LFSR (used to generate the PN / data whitening sequence) is used as the output bit for data scrambling. +// PKT_CONFIG1 - General configuration bits for transmission or reception of a packet. +// PKT_CONFIG2 - General packet configuration bits. +// PKT_LEN - Configuration bits for reception of a variable length packet. +// PKT_LEN_FIELD_SOURCE - Field number containing the received packet length byte(s). +// PKT_LEN_ADJUST - Provides for adjustment/offset of the received packet length value (in order to accommodate a variety of methods of defining total packet length). +// PKT_TX_THRESHOLD - TX FIFO almost empty threshold. +*/ +#define RF_PKT_CRC_CONFIG_12 0x11, 0x12, 0x0C, 0x00, 0x00, 0x01, 0x08, 0xFF, 0xFF, 0x20, 0x02, 0x00, 0x00, 0x00, 0x00, 0x30 + +/* +// Set properties: RF_PKT_RX_THRESHOLD_12 +// Number of properties: 12 +// Group ID: 0x12 +// Start ID: 0x0C +// Default values: 0x30, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, +// Descriptions: +// PKT_RX_THRESHOLD - RX FIFO Almost Full threshold. +// PKT_FIELD_1_LENGTH_12_8 - Unsigned 13-bit Field 1 length value. +// PKT_FIELD_1_LENGTH_7_0 - Unsigned 13-bit Field 1 length value. +// PKT_FIELD_1_CONFIG - General data processing and packet configuration bits for Field 1. +// PKT_FIELD_1_CRC_CONFIG - Configuration of CRC control bits across Field 1. +// PKT_FIELD_2_LENGTH_12_8 - Unsigned 13-bit Field 2 length value. +// PKT_FIELD_2_LENGTH_7_0 - Unsigned 13-bit Field 2 length value. +// PKT_FIELD_2_CONFIG - General data processing and packet configuration bits for Field 2. +// PKT_FIELD_2_CRC_CONFIG - Configuration of CRC control bits across Field 2. +// PKT_FIELD_3_LENGTH_12_8 - Unsigned 13-bit Field 3 length value. +// PKT_FIELD_3_LENGTH_7_0 - Unsigned 13-bit Field 3 length value. +// PKT_FIELD_3_CONFIG - General data processing and packet configuration bits for Field 3. +*/ +#define RF_PKT_RX_THRESHOLD_12 0x11, 0x12, 0x0C, 0x0C, 0x30, 0x00, 0x01, 0x04, 0x00, 0x00, 0x07, 0x00, 0x00, 0x00, 0x00, 0x00 + +/* +// Set properties: RF_PKT_FIELD_3_CRC_CONFIG_12 +// Number of properties: 12 +// Group ID: 0x12 +// Start ID: 0x18 +// Default values: 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, +// Descriptions: +// PKT_FIELD_3_CRC_CONFIG - Configuration of CRC control bits across Field 3. +// PKT_FIELD_4_LENGTH_12_8 - Unsigned 13-bit Field 4 length value. +// PKT_FIELD_4_LENGTH_7_0 - Unsigned 13-bit Field 4 length value. +// PKT_FIELD_4_CONFIG - General data processing and packet configuration bits for Field 4. +// PKT_FIELD_4_CRC_CONFIG - Configuration of CRC control bits across Field 4. +// PKT_FIELD_5_LENGTH_12_8 - Unsigned 13-bit Field 5 length value. +// PKT_FIELD_5_LENGTH_7_0 - Unsigned 13-bit Field 5 length value. +// PKT_FIELD_5_CONFIG - General data processing and packet configuration bits for Field 5. +// PKT_FIELD_5_CRC_CONFIG - Configuration of CRC control bits across Field 5. +// PKT_RX_FIELD_1_LENGTH_12_8 - Unsigned 13-bit RX Field 1 length value. +// PKT_RX_FIELD_1_LENGTH_7_0 - Unsigned 13-bit RX Field 1 length value. +// PKT_RX_FIELD_1_CONFIG - General data processing and packet configuration bits for RX Field 1. +*/ +#define RF_PKT_FIELD_3_CRC_CONFIG_12 0x11, 0x12, 0x0C, 0x18, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00 + +/* +// Set properties: RF_PKT_RX_FIELD_1_CRC_CONFIG_12 +// Number of properties: 12 +// Group ID: 0x12 +// Start ID: 0x24 +// Default values: 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, +// Descriptions: +// PKT_RX_FIELD_1_CRC_CONFIG - Configuration of CRC control bits across RX Field 1. +// PKT_RX_FIELD_2_LENGTH_12_8 - Unsigned 13-bit RX Field 2 length value. +// PKT_RX_FIELD_2_LENGTH_7_0 - Unsigned 13-bit RX Field 2 length value. +// PKT_RX_FIELD_2_CONFIG - General data processing and packet configuration bits for RX Field 2. +// PKT_RX_FIELD_2_CRC_CONFIG - Configuration of CRC control bits across RX Field 2. +// PKT_RX_FIELD_3_LENGTH_12_8 - Unsigned 13-bit RX Field 3 length value. +// PKT_RX_FIELD_3_LENGTH_7_0 - Unsigned 13-bit RX Field 3 length value. +// PKT_RX_FIELD_3_CONFIG - General data processing and packet configuration bits for RX Field 3. +// PKT_RX_FIELD_3_CRC_CONFIG - Configuration of CRC control bits across RX Field 3. +// PKT_RX_FIELD_4_LENGTH_12_8 - Unsigned 13-bit RX Field 4 length value. +// PKT_RX_FIELD_4_LENGTH_7_0 - Unsigned 13-bit RX Field 4 length value. +// PKT_RX_FIELD_4_CONFIG - General data processing and packet configuration bits for RX Field 4. +*/ +#define RF_PKT_RX_FIELD_1_CRC_CONFIG_12 0x11, 0x12, 0x0C, 0x24, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00 + +/* +// Set properties: RF_PKT_RX_FIELD_4_CRC_CONFIG_5 +// Number of properties: 5 +// Group ID: 0x12 +// Start ID: 0x30 +// Default values: 0x00, 0x00, 0x00, 0x00, 0x00, +// Descriptions: +// PKT_RX_FIELD_4_CRC_CONFIG - Configuration of CRC control bits across RX Field 4. +// PKT_RX_FIELD_5_LENGTH_12_8 - Unsigned 13-bit RX Field 5 length value. +// PKT_RX_FIELD_5_LENGTH_7_0 - Unsigned 13-bit RX Field 5 length value. +// PKT_RX_FIELD_5_CONFIG - General data processing and packet configuration bits for RX Field 5. +// PKT_RX_FIELD_5_CRC_CONFIG - Configuration of CRC control bits across RX Field 5. +*/ +#define RF_PKT_RX_FIELD_4_CRC_CONFIG_5 0x11, 0x12, 0x05, 0x30, 0x00, 0x00, 0x00, 0x00, 0x00 + +/* +// Set properties: RF_PKT_CRC_SEED_31_24_4 +// Number of properties: 4 +// Group ID: 0x12 +// Start ID: 0x36 +// Default values: 0x00, 0x00, 0x00, 0x00, +// Descriptions: +// PKT_CRC_SEED_31_24 - 32-bit seed value for the 32-bit CRC engine +// PKT_CRC_SEED_23_16 - 32-bit seed value for the 32-bit CRC engine +// PKT_CRC_SEED_15_8 - 32-bit seed value for the 32-bit CRC engine +// PKT_CRC_SEED_7_0 - 32-bit seed value for the 32-bit CRC engine +*/ +#define RF_PKT_CRC_SEED_31_24_4 0x11, 0x12, 0x04, 0x36, 0x00, 0x00, 0x00, 0x00 + +/* +// Set properties: RF_MODEM_MOD_TYPE_12 +// Number of properties: 12 +// Group ID: 0x20 +// Start ID: 0x00 +// Default values: 0x02, 0x80, 0x07, 0x0F, 0x42, 0x40, 0x01, 0xC9, 0xC3, 0x80, 0x00, 0x06, +// Descriptions: +// MODEM_MOD_TYPE - Selects the type of modulation. In TX mode, additionally selects the source of the modulation. +// MODEM_MAP_CONTROL - Controls polarity and mapping of transmit and receive bits. +// MODEM_DSM_CTRL - Miscellaneous control bits for the Delta-Sigma Modulator (DSM) in the PLL Synthesizer. +// MODEM_DATA_RATE_2 - Unsigned 24-bit value used to determine the TX data rate +// MODEM_DATA_RATE_1 - Unsigned 24-bit value used to determine the TX data rate +// MODEM_DATA_RATE_0 - Unsigned 24-bit value used to determine the TX data rate +// MODEM_TX_NCO_MODE_3 - TX Gaussian filter oversampling ratio and Byte 3 of unsigned 26-bit TX Numerically Controlled Oscillator (NCO) modulus. +// MODEM_TX_NCO_MODE_2 - TX Gaussian filter oversampling ratio and Byte 3 of unsigned 26-bit TX Numerically Controlled Oscillator (NCO) modulus. +// MODEM_TX_NCO_MODE_1 - TX Gaussian filter oversampling ratio and Byte 3 of unsigned 26-bit TX Numerically Controlled Oscillator (NCO) modulus. +// MODEM_TX_NCO_MODE_0 - TX Gaussian filter oversampling ratio and Byte 3 of unsigned 26-bit TX Numerically Controlled Oscillator (NCO) modulus. +// MODEM_FREQ_DEV_2 - 17-bit unsigned TX frequency deviation word. +// MODEM_FREQ_DEV_1 - 17-bit unsigned TX frequency deviation word. +*/ +#define RF_MODEM_MOD_TYPE_12 0x11, 0x20, 0x0C, 0x00, 0x00, 0x00, 0x07, 0x00, 0x27, 0x10, 0x01, 0xC9, 0xC3, 0x80, 0x00, 0x01 + +/* +// Set properties: RF_MODEM_FREQ_DEV_0_1 +// Number of properties: 1 +// Group ID: 0x20 +// Start ID: 0x0C +// Default values: 0xD3, +// Descriptions: +// MODEM_FREQ_DEV_0 - 17-bit unsigned TX frequency deviation word. +*/ +#define RF_MODEM_FREQ_DEV_0_1 0x11, 0x20, 0x01, 0x0C, 0xA3 + +/* +// Set properties: RF_MODEM_TX_RAMP_DELAY_12 +// Number of properties: 12 +// Group ID: 0x20 +// Start ID: 0x18 +// Default values: 0x01, 0x00, 0x08, 0x03, 0xC0, 0x00, 0x10, 0x20, 0x00, 0x00, 0x00, 0x4B, +// Descriptions: +// MODEM_TX_RAMP_DELAY - TX ramp-down delay setting. +// MODEM_MDM_CTRL - MDM control. +// MODEM_IF_CONTROL - Selects Fixed-IF, Scaled-IF, or Zero-IF mode of RX Modem operation. +// MODEM_IF_FREQ_2 - the IF frequency setting (an 18-bit signed number). +// MODEM_IF_FREQ_1 - the IF frequency setting (an 18-bit signed number). +// MODEM_IF_FREQ_0 - the IF frequency setting (an 18-bit signed number). +// MODEM_DECIMATION_CFG1 - Specifies three decimator ratios for the Cascaded Integrator Comb (CIC) filter. +// MODEM_DECIMATION_CFG0 - Specifies miscellaneous parameters and decimator ratios for the Cascaded Integrator Comb (CIC) filter. +// MODEM_DECIMATION_CFG2 - Specifies miscellaneous decimator filter selections. +// MODEM_IFPKD_THRESHOLDS - +// MODEM_BCR_OSR_1 - RX BCR/Slicer oversampling rate (12-bit unsigned number). +// MODEM_BCR_OSR_0 - RX BCR/Slicer oversampling rate (12-bit unsigned number). +*/ +#define RF_MODEM_TX_RAMP_DELAY_12 0x11, 0x20, 0x0C, 0x18, 0x01, 0x80, 0x08, 0x02, 0x80, 0x00, 0x70, 0x10, 0x14, 0xE8, 0x02, 0x71 + +/* +// Set properties: RF_MODEM_BCR_NCO_OFFSET_2_12 +// Number of properties: 12 +// Group ID: 0x20 +// Start ID: 0x24 +// Default values: 0x06, 0xD3, 0xA0, 0x06, 0xD3, 0x02, 0xC0, 0x00, 0x00, 0x23, 0x83, 0x69, +// Descriptions: +// MODEM_BCR_NCO_OFFSET_2 - RX BCR NCO offset value (an unsigned 22-bit number). +// MODEM_BCR_NCO_OFFSET_1 - RX BCR NCO offset value (an unsigned 22-bit number). +// MODEM_BCR_NCO_OFFSET_0 - RX BCR NCO offset value (an unsigned 22-bit number). +// MODEM_BCR_GAIN_1 - The unsigned 11-bit RX BCR loop gain value. +// MODEM_BCR_GAIN_0 - The unsigned 11-bit RX BCR loop gain value. +// MODEM_BCR_GEAR - RX BCR loop gear control. +// MODEM_BCR_MISC1 - Miscellaneous control bits for the RX BCR loop. +// MODEM_BCR_MISC0 - Miscellaneous RX BCR loop controls. +// MODEM_AFC_GEAR - RX AFC loop gear control. +// MODEM_AFC_WAIT - RX AFC loop wait time control. +// MODEM_AFC_GAIN_1 - Sets the gain of the PLL-based AFC acquisition loop, and provides miscellaneous control bits for AFC functionality. +// MODEM_AFC_GAIN_0 - Sets the gain of the PLL-based AFC acquisition loop, and provides miscellaneous control bits for AFC functionality. +*/ +#define RF_MODEM_BCR_NCO_OFFSET_2_12 0x11, 0x20, 0x0C, 0x24, 0x00, 0xD1, 0xB7, 0x00, 0x69, 0x02, 0xC2, 0x00, 0x04, 0x23, 0x80, 0x09 + +/* +// Set properties: RF_MODEM_AFC_LIMITER_1_3 +// Number of properties: 3 +// Group ID: 0x20 +// Start ID: 0x30 +// Default values: 0x00, 0x40, 0xA0, +// Descriptions: +// MODEM_AFC_LIMITER_1 - Set the AFC limiter value. +// MODEM_AFC_LIMITER_0 - Set the AFC limiter value. +// MODEM_AFC_MISC - Specifies miscellaneous AFC control bits. +*/ +#define RF_MODEM_AFC_LIMITER_1_3 0x11, 0x20, 0x03, 0x30, 0x24, 0x15, 0x80 + +/* +// Set properties: RF_MODEM_AGC_CONTROL_1 +// Number of properties: 1 +// Group ID: 0x20 +// Start ID: 0x35 +// Default values: 0xE0, +// Descriptions: +// MODEM_AGC_CONTROL - Miscellaneous control bits for the Automatic Gain Control (AGC) function in the RX Chain. +*/ +#define RF_MODEM_AGC_CONTROL_1 0x11, 0x20, 0x01, 0x35, 0xE0 + +/* +// Set properties: RF_MODEM_AGC_WINDOW_SIZE_12 +// Number of properties: 12 +// Group ID: 0x20 +// Start ID: 0x38 +// Default values: 0x11, 0x10, 0x10, 0x0B, 0x1C, 0x40, 0x00, 0x00, 0x2B, 0x0C, 0xA4, 0x03, +// Descriptions: +// MODEM_AGC_WINDOW_SIZE - Specifies the size of the measurement and settling windows for the AGC algorithm. +// MODEM_AGC_RFPD_DECAY - Sets the decay time of the RF peak detectors. +// MODEM_AGC_IFPD_DECAY - Sets the decay time of the IF peak detectors. +// MODEM_FSK4_GAIN1 - Specifies the gain factor of the secondary branch in 4(G)FSK ISI-suppression. +// MODEM_FSK4_GAIN0 - Specifies the gain factor of the primary branch in 4(G)FSK ISI-suppression. +// MODEM_FSK4_TH1 - 16 bit 4(G)FSK slicer threshold. +// MODEM_FSK4_TH0 - 16 bit 4(G)FSK slicer threshold. +// MODEM_FSK4_MAP - 4(G)FSK symbol mapping code. +// MODEM_OOK_PDTC - Configures the attack and decay times of the OOK Peak Detector. +// MODEM_OOK_BLOPK - Configures the slicing reference level of the OOK Peak Detector. +// MODEM_OOK_CNT1 - OOK control. +// MODEM_OOK_MISC - Selects the detector(s) used for demodulation of an OOK signal, or for demodulation of a (G)FSK signal when using the asynchronous demodulator. +*/ +#define RF_MODEM_AGC_WINDOW_SIZE_12 0x11, 0x20, 0x0C, 0x38, 0x11, 0x89, 0x89, 0x80, 0x02, 0xFF, 0xFF, 0x00, 0x2B, 0x0C, 0xA4, 0x22 + +/* +// Set properties: RF_MODEM_RAW_CONTROL_10 +// Number of properties: 10 +// Group ID: 0x20 +// Start ID: 0x45 +// Default values: 0x02, 0x00, 0xA3, 0x02, 0x80, 0xFF, 0x0C, 0x01, 0x00, 0x40, +// Descriptions: +// MODEM_RAW_CONTROL - Defines gain and enable controls for raw / nonstandard mode. +// MODEM_RAW_EYE_1 - 11 bit eye-open detector threshold. +// MODEM_RAW_EYE_0 - 11 bit eye-open detector threshold. +// MODEM_ANT_DIV_MODE - Antenna diversity mode settings. +// MODEM_ANT_DIV_CONTROL - Specifies controls for the Antenna Diversity algorithm. +// MODEM_RSSI_THRESH - Configures the RSSI threshold. +// MODEM_RSSI_JUMP_THRESH - Configures the RSSI Jump Detection threshold. +// MODEM_RSSI_CONTROL - Control of the averaging modes and latching time for reporting RSSI value(s). +// MODEM_RSSI_CONTROL2 - RSSI Jump Detection control. +// MODEM_RSSI_COMP - RSSI compensation value. +*/ +#define RF_MODEM_RAW_CONTROL_10 0x11, 0x20, 0x0A, 0x45, 0x83, 0x00, 0xCC, 0x01, 0x00, 0xFF, 0x06, 0x00, 0x18, 0x40 + +/* +// Set properties: RF_MODEM_RAW_SEARCH2_2 +// Number of properties: 2 +// Group ID: 0x20 +// Start ID: 0x50 +// Default values: 0x00, 0x08, +// Descriptions: +// MODEM_RAW_SEARCH2 - Defines and controls the search period length for the Moving Average and Min-Max detectors. +// MODEM_CLKGEN_BAND - Select PLL Synthesizer output divider ratio as a function of frequency band. +*/ +#define RF_MODEM_RAW_SEARCH2_2 0x11, 0x20, 0x02, 0x50, 0x84, 0x0D + +/* +// Set properties: RF_MODEM_SPIKE_DET_2 +// Number of properties: 2 +// Group ID: 0x20 +// Start ID: 0x54 +// Default values: 0x00, 0x00, +// Descriptions: +// MODEM_SPIKE_DET - Configures the threshold for (G)FSK Spike Detection. +// MODEM_ONE_SHOT_AFC - Configures parameters for th e One Shot AFC function and for BCR timing/acquisition. +*/ +#define RF_MODEM_SPIKE_DET_2 0x11, 0x20, 0x02, 0x54, 0x03, 0x07 + +/* +// Set properties: RF_MODEM_RSSI_MUTE_1 +// Number of properties: 1 +// Group ID: 0x20 +// Start ID: 0x57 +// Default values: 0x00, +// Descriptions: +// MODEM_RSSI_MUTE - Configures muting of the RSSI to avoid false RSSI interrupts. +*/ +#define RF_MODEM_RSSI_MUTE_1 0x11, 0x20, 0x01, 0x57, 0x00 + +/* +// Set properties: RF_MODEM_DSA_CTRL1_5 +// Number of properties: 5 +// Group ID: 0x20 +// Start ID: 0x5B +// Default values: 0x00, 0x00, 0x00, 0x00, 0x00, +// Descriptions: +// MODEM_DSA_CTRL1 - Configures parameters for the Signal Arrival Detection circuit block and algorithm. +// MODEM_DSA_CTRL2 - Configures parameters for the Signal Arrival Detection circuit block and algorithm. +// MODEM_DSA_QUAL - Configures parameters for the Eye Opening qualification m ethod of the Signal Arrival Detection algorithm. +// MODEM_DSA_RSSI - Signal Arrival Detect RSSI Qualifier Config +// MODEM_DSA_MISC - Miscellaneous detection of signal arrival bits. +*/ +#define RF_MODEM_DSA_CTRL1_5 0x11, 0x20, 0x05, 0x5B, 0x40, 0x04, 0x09, 0x78, 0x20 + +/* +// Set properties: RF_MODEM_CHFLT_RX1_CHFLT_COE13_7_0_12 +// Number of properties: 12 +// Group ID: 0x21 +// Start ID: 0x00 +// Default values: 0xFF, 0xBA, 0x0F, 0x51, 0xCF, 0xA9, 0xC9, 0xFC, 0x1B, 0x1E, 0x0F, 0x01, +// Descriptions: +// MODEM_CHFLT_RX1_CHFLT_COE13_7_0 - Filter coefficients for the first set of RX filter coefficients. +// MODEM_CHFLT_RX1_CHFLT_COE12_7_0 - Filter coefficients for the first set of RX filter coefficients. +// MODEM_CHFLT_RX1_CHFLT_COE11_7_0 - Filter coefficients for the first set of RX filter coefficients. +// MODEM_CHFLT_RX1_CHFLT_COE10_7_0 - Filter coefficients for the first set of RX filter coefficients. +// MODEM_CHFLT_RX1_CHFLT_COE9_7_0 - Filter coefficients for the first set of RX filter coefficients. +// MODEM_CHFLT_RX1_CHFLT_COE8_7_0 - Filter coefficients for the first set of RX filter coefficients. +// MODEM_CHFLT_RX1_CHFLT_COE7_7_0 - Filter coefficients for the first set of RX filter coefficients. +// MODEM_CHFLT_RX1_CHFLT_COE6_7_0 - Filter coefficients for the first set of RX filter coefficients. +// MODEM_CHFLT_RX1_CHFLT_COE5_7_0 - Filter coefficients for the first set of RX filter coefficients. +// MODEM_CHFLT_RX1_CHFLT_COE4_7_0 - Filter coefficients for the first set of RX filter coefficients. +// MODEM_CHFLT_RX1_CHFLT_COE3_7_0 - Filter coefficients for the first set of RX filter coefficients. +// MODEM_CHFLT_RX1_CHFLT_COE2_7_0 - Filter coefficients for the first set of RX filter coefficients. +*/ +#define RF_MODEM_CHFLT_RX1_CHFLT_COE13_7_0_12 0x11, 0x21, 0x0C, 0x00, 0xFF, 0xBA, 0x0F, 0x51, 0xCF, 0xA9, 0xC9, 0xFC, 0x1B, 0x1E, 0x0F, 0x01 + +/* +// Set properties: RF_MODEM_CHFLT_RX1_CHFLT_COE1_7_0_12 +// Number of properties: 12 +// Group ID: 0x21 +// Start ID: 0x0C +// Default values: 0xFC, 0xFD, 0x15, 0xFF, 0x00, 0x0F, 0xFF, 0xC4, 0x30, 0x7F, 0xF5, 0xB5, +// Descriptions: +// MODEM_CHFLT_RX1_CHFLT_COE1_7_0 - Filter coefficients for the first set of RX filter coefficients. +// MODEM_CHFLT_RX1_CHFLT_COE0_7_0 - Filter coefficients for the first set of RX filter coefficients. +// MODEM_CHFLT_RX1_CHFLT_COEM0 - Filter coefficients for the first set of RX filter coefficients. +// MODEM_CHFLT_RX1_CHFLT_COEM1 - Filter coefficients for the first set of RX filter coefficients. +// MODEM_CHFLT_RX1_CHFLT_COEM2 - Filter coefficients for the first set of RX filter coefficients. +// MODEM_CHFLT_RX1_CHFLT_COEM3 - Filter coefficients for the first set of RX filter coefficients. +// MODEM_CHFLT_RX2_CHFLT_COE13_7_0 - Filter coefficients for the second set of RX filter coefficients. +// MODEM_CHFLT_RX2_CHFLT_COE12_7_0 - Filter coefficients for the second set of RX filter coefficients. +// MODEM_CHFLT_RX2_CHFLT_COE11_7_0 - Filter coefficients for the second set of RX filter coefficients. +// MODEM_CHFLT_RX2_CHFLT_COE10_7_0 - Filter coefficients for the second set of RX filter coefficients. +// MODEM_CHFLT_RX2_CHFLT_COE9_7_0 - Filter coefficients for the second set of RX filter coefficients. +// MODEM_CHFLT_RX2_CHFLT_COE8_7_0 - Filter coefficients for the second set of RX filter coefficients. +*/ +#define RF_MODEM_CHFLT_RX1_CHFLT_COE1_7_0_12 0x11, 0x21, 0x0C, 0x0C, 0xFC, 0xFD, 0x15, 0xFF, 0x00, 0x0F, 0xFF, 0xBA, 0x0F, 0x51, 0xCF, 0xA9 + +/* +// Set properties: RF_MODEM_CHFLT_RX2_CHFLT_COE7_7_0_12 +// Number of properties: 12 +// Group ID: 0x21 +// Start ID: 0x18 +// Default values: 0xB8, 0xDE, 0x05, 0x17, 0x16, 0x0C, 0x03, 0x00, 0x15, 0xFF, 0x00, 0x00, +// Descriptions: +// MODEM_CHFLT_RX2_CHFLT_COE7_7_0 - Filter coefficients for the second set of RX filter coefficients. +// MODEM_CHFLT_RX2_CHFLT_COE6_7_0 - Filter coefficients for the second set of RX filter coefficients. +// MODEM_CHFLT_RX2_CHFLT_COE5_7_0 - Filter coefficients for the second set of RX filter coefficients. +// MODEM_CHFLT_RX2_CHFLT_COE4_7_0 - Filter coefficients for the second set of RX filter coefficients. +// MODEM_CHFLT_RX2_CHFLT_COE3_7_0 - Filter coefficients for the second set of RX filter coefficients. +// MODEM_CHFLT_RX2_CHFLT_COE2_7_0 - Filter coefficients for the second set of RX filter coefficients. +// MODEM_CHFLT_RX2_CHFLT_COE1_7_0 - Filter coefficients for the second set of RX filter coefficients. +// MODEM_CHFLT_RX2_CHFLT_COE0_7_0 - Filter coefficients for the second set of RX filter coefficients. +// MODEM_CHFLT_RX2_CHFLT_COEM0 - Filter coefficients for the second set of RX filter coefficients. +// MODEM_CHFLT_RX2_CHFLT_COEM1 - Filter coefficients for the second set of RX filter coefficients. +// MODEM_CHFLT_RX2_CHFLT_COEM2 - Filter coefficients for the second set of RX filter coefficients. +// MODEM_CHFLT_RX2_CHFLT_COEM3 - Filter coefficients for the second set of RX filter coefficients. +*/ +#define RF_MODEM_CHFLT_RX2_CHFLT_COE7_7_0_12 0x11, 0x21, 0x0C, 0x18, 0xC9, 0xFC, 0x1B, 0x1E, 0x0F, 0x01, 0xFC, 0xFD, 0x15, 0xFF, 0x00, 0x0F + +/* +// Set properties: RF_PA_MODE_4 +// Number of properties: 4 +// Group ID: 0x22 +// Start ID: 0x00 +// Default values: 0x08, 0x7F, 0x00, 0x5D, +// Descriptions: +// PA_MODE - Selects the PA operating mode, and selects resolution of PA power adjustment (i.e., step size). +// PA_PWR_LVL - Configuration of PA output power level. +// PA_BIAS_CLKDUTY - Configuration of the PA Bias and duty cycle of the TX clock source. +// PA_TC - Configuration of PA ramping parameters. +*/ +#define RF_PA_MODE_4 0x11, 0x22, 0x04, 0x00, 0x08, 0x7F, 0x00, 0x1D + +/* +// Set properties: RF_SYNTH_PFDCP_CPFF_7 +// Number of properties: 7 +// Group ID: 0x23 +// Start ID: 0x00 +// Default values: 0x2C, 0x0E, 0x0B, 0x04, 0x0C, 0x73, 0x03, +// Descriptions: +// SYNTH_PFDCP_CPFF - Feed forward charge pump current selection. +// SYNTH_PFDCP_CPINT - Integration charge pump current selection. +// SYNTH_VCO_KV - Gain scaling factors (Kv) for the VCO tuning varactors on both the integrated-path and feed forward path. +// SYNTH_LPFILT3 - Value of resistor R2 in feed-forward path of loop filter. +// SYNTH_LPFILT2 - Value of capacitor C2 in feed-forward path of loop filter. +// SYNTH_LPFILT1 - Value of capacitors C1 and C3 in feed-forward path of loop filter. +// SYNTH_LPFILT0 - Bias current of the active amplifier in the feed-forward loop filter. +*/ +#define RF_SYNTH_PFDCP_CPFF_7 0x11, 0x23, 0x07, 0x00, 0x2C, 0x0E, 0x0B, 0x04, 0x0C, 0x73, 0x03 + +/* +// Set properties: RF_MATCH_VALUE_1_12 +// Number of properties: 12 +// Group ID: 0x30 +// Start ID: 0x00 +// Default values: 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, +// Descriptions: +// MATCH_VALUE_1 - Match value to be compared with the result of logically AND-ing (bit-wise) the Mask 1 value with the received Match 1 byte. +// MATCH_MASK_1 - Mask value to be logically AND-ed (bit-wise) with the Match 1 byte. +// MATCH_CTRL_1 - Enable for Packet Match functionality, and configuration of Match Byte 1. +// MATCH_VALUE_2 - Match value to be compared with the result of logically AND-ing (bit-wise) the Mask 2 value with the received Match 2 byte. +// MATCH_MASK_2 - Mask value to be logically AND-ed (bit-wise) with the Match 2 byte. +// MATCH_CTRL_2 - Configuration of Match Byte 2. +// MATCH_VALUE_3 - Match value to be compared with the result of logically AND-ing (bit-wise) the Mask 3 value with the received Match 3 byte. +// MATCH_MASK_3 - Mask value to be logically AND-ed (bit-wise) with the Match 3 byte. +// MATCH_CTRL_3 - Configuration of Match Byte 3. +// MATCH_VALUE_4 - Match value to be compared with the result of logically AND-ing (bit-wise) the Mask 4 value with the received Match 4 byte. +// MATCH_MASK_4 - Mask value to be logically AND-ed (bit-wise) with the Match 4 byte. +// MATCH_CTRL_4 - Configuration of Match Byte 4. +*/ +#define RF_MATCH_VALUE_1_12 0x11, 0x30, 0x0C, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00 + +/* +// Set properties: RF_FREQ_CONTROL_INTE_8 +// Number of properties: 8 +// Group ID: 0x40 +// Start ID: 0x00 +// Default values: 0x3C, 0x08, 0x00, 0x00, 0x00, 0x00, 0x20, 0xFF, +// Descriptions: +// FREQ_CONTROL_INTE - Frac-N PLL Synthesizer integer divide number. +// FREQ_CONTROL_FRAC_2 - Frac-N PLL fraction number. +// FREQ_CONTROL_FRAC_1 - Frac-N PLL fraction number. +// FREQ_CONTROL_FRAC_0 - Frac-N PLL fraction number. +// FREQ_CONTROL_CHANNEL_STEP_SIZE_1 - EZ Frequency Programming channel step size. +// FREQ_CONTROL_CHANNEL_STEP_SIZE_0 - EZ Frequency Programming channel step size. +// FREQ_CONTROL_W_SIZE - Set window gating period (in number of crystal reference clock cycles) for counting VCO frequency during calibration. +// FREQ_CONTROL_VCOCNT_RX_ADJ - Adjust target count for VCO calibration in RX mode. +*/ +#define RF_FREQ_CONTROL_INTE_8 0x11, 0x40, 0x08, 0x00, 0x42, 0x0E, 0x14, 0x7A, 0xCC, 0xCD, 0x20, 0xFA + + +// AUTOMATICALLY GENERATED CODE! +// DO NOT EDIT/MODIFY BELOW THIS LINE! +// -------------------------------------------- + +#ifndef FIRMWARE_LOAD_COMPILE +#define RADIO_CONFIGURATION_DATA_ARRAY { \ + 0x07, RF_POWER_UP, \ + 0x08, RF_GPIO_PIN_CFG, \ + 0x06, RF_GLOBAL_XO_TUNE_2, \ + 0x05, RF_GLOBAL_CONFIG_1, \ + 0x06, RF_INT_CTL_ENABLE_2, \ + 0x08, RF_FRR_CTL_A_MODE_4, \ + 0x0D, RF_PREAMBLE_TX_LENGTH_9, \ + 0x0E, RF_SYNC_CONFIG_10, \ + 0x10, RF_PKT_CRC_CONFIG_12, \ + 0x10, RF_PKT_RX_THRESHOLD_12, \ + 0x10, RF_PKT_FIELD_3_CRC_CONFIG_12, \ + 0x10, RF_PKT_RX_FIELD_1_CRC_CONFIG_12, \ + 0x09, RF_PKT_RX_FIELD_4_CRC_CONFIG_5, \ + 0x08, RF_PKT_CRC_SEED_31_24_4, \ + 0x10, RF_MODEM_MOD_TYPE_12, \ + 0x05, RF_MODEM_FREQ_DEV_0_1, \ + 0x10, RF_MODEM_TX_RAMP_DELAY_12, \ + 0x10, RF_MODEM_BCR_NCO_OFFSET_2_12, \ + 0x07, RF_MODEM_AFC_LIMITER_1_3, \ + 0x05, RF_MODEM_AGC_CONTROL_1, \ + 0x10, RF_MODEM_AGC_WINDOW_SIZE_12, \ + 0x0E, RF_MODEM_RAW_CONTROL_10, \ + 0x06, RF_MODEM_RAW_SEARCH2_2, \ + 0x06, RF_MODEM_SPIKE_DET_2, \ + 0x05, RF_MODEM_RSSI_MUTE_1, \ + 0x09, RF_MODEM_DSA_CTRL1_5, \ + 0x10, RF_MODEM_CHFLT_RX1_CHFLT_COE13_7_0_12, \ + 0x10, RF_MODEM_CHFLT_RX1_CHFLT_COE1_7_0_12, \ + 0x10, RF_MODEM_CHFLT_RX2_CHFLT_COE7_7_0_12, \ + 0x08, RF_PA_MODE_4, \ + 0x0B, RF_SYNTH_PFDCP_CPFF_7, \ + 0x10, RF_MATCH_VALUE_1_12, \ + 0x0C, RF_FREQ_CONTROL_INTE_8, \ + 0x00 \ + } +#else +#define RADIO_CONFIGURATION_DATA_ARRAY { 0 } +#endif + +// DEFAULT VALUES FOR CONFIGURATION PARAMETERS +#define RADIO_CONFIGURATION_DATA_RADIO_XO_FREQ_DEFAULT 30000000L +#define RADIO_CONFIGURATION_DATA_CHANNEL_NUMBER_DEFAULT 0x00 +#define RADIO_CONFIGURATION_DATA_RADIO_PACKET_LENGTH_DEFAULT 0x10 +#define RADIO_CONFIGURATION_DATA_RADIO_STATE_AFTER_POWER_UP_DEFAULT 0x01 +#define RADIO_CONFIGURATION_DATA_RADIO_DELAY_CNT_AFTER_RESET_DEFAULT 0x1000 + +#define RADIO_CONFIGURATION_DATA_RADIO_PATCH_INCLUDED 0x00 +#define RADIO_CONFIGURATION_DATA_RADIO_PATCH_SIZE 0x00 +#define RADIO_CONFIGURATION_DATA_RADIO_PATCH { } + +#ifndef RADIO_CONFIGURATION_DATA_ARRAY +#error "This property must be defined!" +#endif + +#ifndef RADIO_CONFIGURATION_DATA_RADIO_XO_FREQ +#define RADIO_CONFIGURATION_DATA_RADIO_XO_FREQ RADIO_CONFIGURATION_DATA_RADIO_XO_FREQ_DEFAULT +#endif + +#ifndef RADIO_CONFIGURATION_DATA_CHANNEL_NUMBER +#define RADIO_CONFIGURATION_DATA_CHANNEL_NUMBER RADIO_CONFIGURATION_DATA_CHANNEL_NUMBER_DEFAULT +#endif + +#ifndef RADIO_CONFIGURATION_DATA_RADIO_PACKET_LENGTH +#define RADIO_CONFIGURATION_DATA_RADIO_PACKET_LENGTH RADIO_CONFIGURATION_DATA_RADIO_PACKET_LENGTH_DEFAULT +#endif + +#ifndef RADIO_CONFIGURATION_DATA_RADIO_STATE_AFTER_POWER_UP +#define RADIO_CONFIGURATION_DATA_RADIO_STATE_AFTER_POWER_UP RADIO_CONFIGURATION_DATA_RADIO_STATE_AFTER_POWER_UP_DEFAULT +#endif + +#ifndef RADIO_CONFIGURATION_DATA_RADIO_DELAY_CNT_AFTER_RESET +#define RADIO_CONFIGURATION_DATA_RADIO_DELAY_CNT_AFTER_RESET RADIO_CONFIGURATION_DATA_RADIO_DELAY_CNT_AFTER_RESET_DEFAULT +#endif + +#define RADIO_CONFIGURATION_DATA { \ + Radio_Configuration_Data_Array, \ + RADIO_CONFIGURATION_DATA_CHANNEL_NUMBER, \ + RADIO_CONFIGURATION_DATA_RADIO_PACKET_LENGTH, \ + RADIO_CONFIGURATION_DATA_RADIO_STATE_AFTER_POWER_UP, \ + RADIO_CONFIGURATION_DATA_RADIO_DELAY_CNT_AFTER_RESET \ + } + +#endif /* RADIO_CONFIG_H_ */ diff --git a/firmware/inc/driver/si4468.h b/firmware/inc/driver/si4468.h new file mode 100644 index 0000000..61e72e5 --- /dev/null +++ b/firmware/inc/driver/si4468.h @@ -0,0 +1,54 @@ +/** + * + * Author: Dylan Muller + * Copyright (c) 2025 + * All rights reserved. + * + * - Commercial/IP use prohibited. + * - Attribution required. + * See License.txt + * + */ + +#ifndef SI4468_H_ +#define SI4468_H_ + +#include "setup.h" + +#include <stdint.h> +#include <avr/io.h> + +#define SI4468_ID_RADIO 0xD1 + +#define SI4468_CMD_READ_CMD_BUFF 0x44 +#define SI4468_CMD_PART_INFO 0x01 +#define SI4468_CMD_FUNC_INFO 0x10 +#define SI4468_CMD_SET_PROPERTY 0x11 +#define SI4468_CMD_IRCAL 0x17 +#define SI4468_CMD_START_TX 0x31 +#define SI4468_CMD_CHANGE_STATE 0x34 + +#define SI4468_CTS 0xFF +#define SI4468_GET_RESP_LEN 0x2 + +#define SI4468_DEV_0 0 +#define SI4468_DEV_RADIO SI4468_DEV_0 +#define SI4468_DEV_0_PORT PORTB +#define SI4468_DEV_0_DDR DDRB +#define SI4468_DEV_0_SS PORTB2 + +typedef struct { + uint8_t chipRev; + uint16_t part; + uint8_t partBuild; + uint16_t id; + uint8_t customer; + uint8_t romId; ///< ROM ID (3 = revB1B, 6 = revC2A) +} si4468_info_t; + +void si4468_init(void); +void si4468_get_info(si4468_info_t* info); +void si4468_apply_startup_config(void); +void si4468_tx_mode(void); +void si4468_rx_mode(void); +#endif diff --git a/firmware/inc/module/drain.h b/firmware/inc/module/drain.h new file mode 100644 index 0000000..7b9d66d --- /dev/null +++ b/firmware/inc/module/drain.h @@ -0,0 +1,37 @@ +/** + * + * Author: Dylan Muller + * Copyright (c) 2025 + * All rights reserved. + * + * - Commercial/IP use prohibited. + * - Attribution required. + * See License.txt + * + */ + +#ifndef DRAIN_H_ +#define DRAIN_H_ + +#include <stdint.h> + +#define DRAIN_PROBE_START 0 // mV +#define DRAIN_PROBE_LIMIT 3000 +#define DRAIN_PROBE_INC_FINE 1 +#define DRAIN_PROBE_INC_COARSE 5 +#define DRAIN_PROBE_INC_THRESHOLD 100 +#define DRAIN_Q_AMP 100 // mA +#define DRAIN_TEST_COUNT 10 +#define DRAIN_TEST_BOUNDARY 10 +#define DRAIN_POWER_SAMPLES 10 +#define DRAIN_LOOP_DELAY_US 1000 +#define DRAIN_SETPOINT_TIMEOUT_MS 1500 +#define DRAIN_POWER_LOW_LIM 0 +#define DRAIN_POWER_HIGH_LIM 3000 +#define DRAIN_POWER_MODULUS 50 + +uint16_t drain_sweep_pwr( + int16_t target_fw_pwr +); + +#endif diff --git a/firmware/inc/module/gate.h b/firmware/inc/module/gate.h new file mode 100644 index 0000000..9f399c4 --- /dev/null +++ b/firmware/inc/module/gate.h @@ -0,0 +1,32 @@ +/** + * + * Author: Dylan Muller + * Copyright (c) 2025 + * All rights reserved. + * + * - Commercial/IP use prohibited. + * - Attribution required. + * See License.txt + * + */ + +#ifndef GATE_H_ +#define GATE_H_ + +#include <stdint.h> +#include <stdbool.h> +#include <util/delay.h> + +#define GATE_PROBE_START 2800 // mV +#define GATE_PROBE_LIMIT 3300 // mV +#define GATE_PROBE_DRAIN 1000 // mV +#define GATE_PROBE_INC 1 // COUNTS +#define GATE_PA_POWER_DOWN 1 +#define GATE_LOOP_DELAY_US 1000 + +uint16_t gate_probe( + uint16_t target_amp, // mA + uint16_t* probe_result +); + +#endif diff --git a/firmware/inc/peripheral/ring.h b/firmware/inc/peripheral/ring.h new file mode 100644 index 0000000..d2a713d --- /dev/null +++ b/firmware/inc/peripheral/ring.h @@ -0,0 +1,77 @@ +/** + * + * Author: Dylan Muller + * Copyright (c) 2025 + * All rights reserved. + * + * - Commercial/IP use prohibited. + * - Attribution required. + * See License.txt + * + */ + +#ifndef RING_H_ +#define RING_H_ + +#include <stdbool.h> +#include <stddef.h> +#include <stdint.h> + +typedef struct +{ + uint8_t *buf; + uint8_t *end; + uint8_t *write; + uint8_t *read; +} ring_t; + +#define RING_INIT(buf_, len_) \ + ((ring_t){ \ + .buf = (buf_), \ + .end = (buf_)+(len_), \ + .write = (buf_), \ + .read = (buf_)} \ + ) + +ring_t ring_init( + uint8_t *buf, + size_t len +); + +bool ring_is_empty( + ring_t ring +); + +bool ring_is_full( + ring_t ring +); + +size_t ring_push_available( + ring_t ring +); + +size_t ring_pop_available( + ring_t ring +); + +bool ring_push( + ring_t *ring, + uint8_t data +); + +bool ring_push_over( + ring_t *ring, + uint8_t data +); + +bool ring_pop( + ring_t *ring, + uint8_t *data +); + +bool ring_peek( + ring_t *ring, + uint8_t *data +); + +#endif diff --git a/firmware/inc/peripheral/spi.h b/firmware/inc/peripheral/spi.h new file mode 100644 index 0000000..003fc04 --- /dev/null +++ b/firmware/inc/peripheral/spi.h @@ -0,0 +1,34 @@ +/** + * + * Author: Dylan Muller + * Copyright (c) 2025 + * All rights reserved. + * + * - Commercial/IP use prohibited. + * - Attribution required. + * See License.txt + * + */ + +#ifndef SPI_H_ +#define SPI_H_ + +#include <stdbool.h> +#include <stddef.h> +#include <stdint.h> + +void spi_init(void); + +bool spi_busy(void); + +void spi_flush(void); + +void spi_start( + uint8_t *out, + uint8_t *in, + size_t len, + uint8_t *port, + uint8_t pin +); + +#endif diff --git a/firmware/inc/peripheral/timer.h b/firmware/inc/peripheral/timer.h new file mode 100644 index 0000000..ff45c85 --- /dev/null +++ b/firmware/inc/peripheral/timer.h @@ -0,0 +1,22 @@ +/** + * + * Author: Dylan Muller + * Copyright (c) 2025 + * All rights reserved. + * + * - Commercial/IP use prohibited. + * - Attribution required. + * See License.txt + * + */ + +#ifndef TIMER_H_ +#define TIMER_H_ + +#include <stdint.h> + +void timer_init(void); +void timer_reset(void); +uint32_t timer_millis(void); + +#endif diff --git a/firmware/inc/peripheral/twi.h b/firmware/inc/peripheral/twi.h new file mode 100644 index 0000000..8f08777 --- /dev/null +++ b/firmware/inc/peripheral/twi.h @@ -0,0 +1,35 @@ +/** + * + * Author: Dylan Muller + * Copyright (c) 2025 + * All rights reserved. + * + * - Commercial/IP use prohibited. + * - Attribution required. + * See License.txt + * + */ + +#ifndef TWI_H_ +#define TWI_H_ + +#include <stdbool.h> +#include <stddef.h> +#include <stdint.h> + +#define TWI_ADDRESS_W(x) (((x) << 1) & ~0x01) +#define TWI_ADDRESS_R(x) (((x) << 1) | 0x01) + +void twi_init(void); + +bool twi_busy(void); + +void twi_flush(void); + +void twi_start( + uint8_t address, + uint8_t *data, + size_t len +); + +#endif diff --git a/firmware/inc/peripheral/uart.h b/firmware/inc/peripheral/uart.h new file mode 100644 index 0000000..e2a0f3d --- /dev/null +++ b/firmware/inc/peripheral/uart.h @@ -0,0 +1,56 @@ +/** + * + * Author: Dylan Muller + * Copyright (c) 2025 + * All rights reserved. + * + * - Commercial/IP use prohibited. + * - Attribution required. + * See License.txt + * + */ + +#ifndef UARTINT_H_ +#define UARTINT_H_ + +#include <stddef.h> +#include <stdint.h> +#include <stdio.h> +#include <stdbool.h> + +extern FILE uart_out; +extern FILE uart_in; + +void uart_init(void); + +bool uart_tx( + uint8_t data +); + +bool uart_rx( + uint8_t* data +); + +size_t uart_tx_burst( + uint8_t* data, + size_t size +); + +size_t uart_rx_burst( + uint8_t* data, + size_t size +); + +size_t uart_tx_available(void); + +size_t uart_rx_available(void); + +bool uart_rx_peek( + uint8_t* data +); + +void uart_tx_flush(void); + +char *uart_ngets(char *s, size_t n); + +#endif diff --git a/firmware/inc/setup.h b/firmware/inc/setup.h new file mode 100644 index 0000000..e01bcd3 --- /dev/null +++ b/firmware/inc/setup.h @@ -0,0 +1,39 @@ +/** + * + * Author: Dylan Muller + * Copyright (c) 2025 + * All rights reserved. + * + * - Commercial/IP use prohibited. + * - Attribution required. + * See License.txt + * + */ + +/* Global Peripheral Configuration*/ + +#define __AVR_ATmega328__ + +#define F_CPU 8000000UL + +#define BAUD 19200 +#define UART_BUF_SIZE 25 +#define UART_OVERWRITE + +#define TWI_FREQUENCY 350000 +#define TWI_PRESCALER 1 +#define TWPS0_VALUE 0 +#define TWPS1_VALUE 0 + +#define SPI_FREQUENCY 500000 +#define SPI_PRESCALER 16 +#define SPR0_VALUE 1 +#define SPR1_VALUE 0 +#define SPI2X_VALUE 0 +#define SPI_MODE 0 +#define SPI_DORD 0 + +#define TRANSACT_DELAY_MS 5 +#define INIT_DELAY_MS 10 + +#define SYS_VER_STR "1.01.5" diff --git a/firmware/inc/status.h b/firmware/inc/status.h new file mode 100644 index 0000000..b9c647b --- /dev/null +++ b/firmware/inc/status.h @@ -0,0 +1,83 @@ +/** + * + * Author: Dylan Muller + * Copyright (c) 2025 + * All rights reserved. + * + * - Commercial/IP use prohibited. + * - Attribution required. + * See License.txt + * + */ + +#ifndef STATUS_H_ +#define STATUS_H_ + +#include <stdint.h> +#include <avr/pgmspace.h> + +extern const char* const gate_lut[]; +extern const char* const drain_lut[]; +extern const char* const system_lut[]; + +enum +{ + GATE_STATUS_INACTIVE = 0, + GATE_STATUS_PROBE_ERROR, + GATE_STATUS_PROBE_SUCCESS, + GATE_STATUS_PROBE_TIMEOUT +}; + +typedef struct { + uint8_t status; + uint16_t q_volt; + uint16_t q_amp; + uint16_t q_time; + uint16_t v_set; + uint16_t q_drain; + uint8_t func; +} t_gate_status; + +enum +{ + DRAIN_STATUS_INACTIVE = 0, + DRAIN_STATUS_POWER_CONTROL, + DRAIN_STATUS_OVERRIDE, + DRAIN_STATUS_ADC_ERROR, + DRAIN_STATUS_CURRENT_ALARM +}; + +typedef struct { + uint8_t status; + uint16_t v_set; + uint16_t v_adc; + uint16_t amp; + uint8_t func; +} t_drain_status; + +enum +{ + SYSTEM_STATUS_IDLE = 0, + SYSTEM_STATUS_BUSY, + SYSTEM_STATUS_LOCKED, + SYSTEM_STATUS_SETPOINT_FAIL, + SYSTEM_STATUS_SETPOINT_REACHED, + SYSTEM_STATUS_SETPOINT_TIMEOUT, + SYSTEM_STATUS_VSWR_ALARM +}; + +typedef struct { + uint8_t status; + uint16_t v_fw; + int16_t p_fw; + uint16_t v_rev; + int16_t p_rev; + uint16_t swr; + uint16_t swr_lim; + uint16_t atten; + uint8_t p_strat; + int16_t p_set; + uint16_t d_time; +} t_system_status; + +#endif diff --git a/firmware/inc/util.h b/firmware/inc/util.h new file mode 100644 index 0000000..5936a3a --- /dev/null +++ b/firmware/inc/util.h @@ -0,0 +1,46 @@ +/** + * + * Author: Dylan Muller + * Copyright (c) 2025 + * All rights reserved. + * + * - Commercial/IP use prohibited. + * - Attribution required. + * See License.txt + * + */ + +#ifndef UTIL_H_ +#define UTIL_H_ + +#include <stdint.h> + +#define UTIL_SYSTEM_VOLT ((uint32_t)3300) // (mV) +#define UTIL_CONV_BITS 12 +#define UTIL_CONV_BIT(x) (1 << x) + +#define UTIL_COUPLER_ATTEN ((int16_t)4250) // BI-DIR COUPL CAL +#define UTIL_POWER_THRESHOLD 2000 + +uint8_t util_volt_to_count( + uint16_t volt, + uint16_t* count +); + +uint8_t util_count_to_volt( + uint16_t count, + uint16_t* volt +); + +int8_t util_count_to_pwr( + uint16_t count, + int16_t* cpwr +); + +void util_print_pwr( + int16_t cpwr +); + +uint16_t util_get_free_mem(void); + +#endif |